U-Boot 1.1.6 (Aug 7 2011 - 16:50:07) for FriendlyARM MINI6410
CPU: S3C6410@532MHz
Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode)
Board: MINI6410
DRAM: 256 MB
Flash: 0 kB
NAND: 256 MB
In: serial
Out: serial
Err: serial
MAC: 08:90:90:90:90:90
Hit any key to stop autoboot: 0
#####U-Boot(2011-05, NAND) for Tiny6410#####
Powered by Lintel 2011
[f] Format the nand flash
[v] Download u-boot.bin
[k] Download Linux/Android kernel
[c] Download root cramfs/squashfs image
[j] Download root jffs2 image
[y] Download root yaffs2 image
Download root ubifs image
[a] Download Absolute User Application
[n] Download Nboot.nb0 for WinCE
[w] Download WinCE NK.nb0
[s] Set the boot parameter of Linux
Boot Linux
[q] Quit to shell
NAND(SLC): 256 MiB, RAM: 256 MiB
LCD type, firmware version: 1 1046
Enter your Selection:c
Downloading OpenWrt Rootfs from USB...
OTG cable Connected!
Download address 0xc0000000
Download Done!! Download Address: 0xc0000000, Download Filesize:0x170000
Checksum is being calculated..
Checksum O.K.
Downloading OpenWrt Rootfs successed
Writing OpenWrt Rootfs into NAND...
Writing data at 0x6ff800 -- 100% complete.
Writing OpenWrt Rootfs successed
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
Linux command line 'root=/dev/mtdblock2 rootfstype=squashfs console=ttySAC0,115200' saved
#####U-Boot(2011-05, NAND) for Tiny6410#####
Powered by Lintel 2011
[f] Format the nand flash
[v] Download u-boot.bin
[k] Download Linux/Android kernel
[c] Download root cramfs/squashfs image
[j] Download root jffs2 image
[y] Download root yaffs2 image
Download root ubifs image
[a] Download Absolute User Application
[n] Download Nboot.nb0 for WinCE
[w] Download WinCE NK.nb0
[s] Set the boot parameter of Linux
Boot Linux
[q] Quit to shell
NAND(SLC): 256 MiB, RAM: 256 MiB
LCD type, firmware version: 1 1046
Enter your Selection:b
NAND read: device 0 offset 0x80000, size 0x500000
........................................Boot with zImage
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.36.4 (lintel@lintel-Aspire-4741) (gcc version 4.3.3 (GCC) ) #30 PREEMPT Sun Aug 7 13:17:26 BST 2011
[ 0.000000] CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: MINI6410
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU S3C6410 (id 0x36410101)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] camera: no parent clock specified
[ 0.000000] S3C64XX: PLL settings, A=532000000, M=532000000, E=24000000
[ 0.000000] S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
[ 0.000000] mout_apll: source is fout_apll (1), rate is 532000000
[ 0.000000] mout_epll: source is epll (1), rate is 24000000
[ 0.000000] mout_mpll: source is mpll (1), rate is 532000000
[ 0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[ 0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[ 0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[ 0.000000] usb-bus-host: source is clk_48m (0), rate is 48000000
[ 0.000000] uclk1: source is dout_mpll (1), rate is 66500000
[ 0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] irda-bus: source is mout_epll (0), rate is 24000000
[ 0.000000] camera: no parent clock specified
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttySAC0,115200
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 255684k/255684k available, 6460k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xe0000000 ( 248 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0024000 ( 112 kB)
[ 0.000000] .text : 0xc0024000 - 0xc03c5000 (3716 kB)
[ 0.000000] .data : 0xc03c6000 - 0xc03e6b80 ( 131 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:246
[ 0.000000] VIC @f4000000: id 0x00041192, vendor 0x41
[ 0.000000] VIC @f4010000: id 0x00041192, vendor 0x41
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttySAC0] enabled
[ 0.020000] Calibrating delay loop... 530.84 BogoMIPS (lpj=2654208)
[ 0.280000] pid_max: default: 32768 minimum: 301
[ 0.280000] Mount-cache hash table entries: 512
[ 0.280000] CPU: Testing write buffer coherency: ok
[ 0.290000] NET: Registered protocol family 16
[ 0.300000] s3c64xx_dma_init: Registering DMA channels
[ 0.300000] s3c64xx_dma_init1: registering DMA 0 (d0808100)
[ 0.310000] s3c64xx_dma_init1: registering DMA 1 (d0808120)
[ 0.310000] s3c64xx_dma_init1: registering DMA 2 (d0808140)
[ 0.320000] s3c64xx_dma_init1: registering DMA 3 (d0808160)
[ 0.320000] s3c64xx_dma_init1: registering DMA 4 (d0808180)
[ 0.330000] s3c64xx_dma_init1: registering DMA 5 (d08081a0)
[ 0.330000] s3c64xx_dma_init1: registering DMA 6 (d08081c0)
[ 0.340000] s3c64xx_dma_init1: registering DMA 7 (d08081e0)
[ 0.340000] PL080: IRQ 73, at d0808000
[ 0.350000] s3c64xx_dma_init1: registering DMA 8 (d080c100)
[ 0.350000] s3c64xx_dma_init1: registering DMA 9 (d080c120)
[ 0.360000] s3c64xx_dma_init1: registering DMA 10 (d080c140)
[ 0.370000] s3c64xx_dma_init1: registering DMA 11 (d080c160)
[ 0.370000] s3c64xx_dma_init1: registering DMA 12 (d080c180)
[ 0.380000] s3c64xx_dma_init1: registering DMA 13 (d080c1a0)
[ 0.380000] s3c64xx_dma_init1: registering DMA 14 (d080c1c0)
[ 0.390000] s3c64xx_dma_init1: registering DMA 15 (d080c1e0)
[ 0.390000] PL080: IRQ 74, at d080c000
[ 0.400000] S3C6410: Initialising architecture
[ 0.450000] bio: create slab <bio-0> at 0
[ 0.450000] SCSI subsystem initialized
[ 0.460000] usbcore: registered new interface driver usbfs
[ 0.460000] usbcore: registered new interface driver hub
[ 0.460000] usbcore: registered new device driver usb
[ 0.470000] s3c-i2c s3c2440-i2c: slave address 0x10
[ 0.470000] s3c-i2c s3c2440-i2c: bus frequency set to 64 KHz
[ 0.480000] s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
[ 0.490000] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.540000] NET: Registered protocol family 2
[ 0.540000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.550000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.560000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.560000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.570000] TCP reno registered
[ 0.570000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.580000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.580000] NET: Registered protocol family 1
[ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.620000] Registering mini_fo version $Id$
[ 0.630000] JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
[ 0.640000] msgmni has been set to 499
[ 0.640000] io scheduler noop registered (default)
[ 0.640000] backlight initialized
[ 1.300000] adc initialized
[ 1.300000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.310000] s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
[ 1.310000] s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
[ 1.320000] s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
[ 1.330000] s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
[ 1.350000] loop: module loaded
[ 1.360000] S3C NAND Driver, (c) 2008 Samsung Electronics
[ 1.360000] S3C NAND Driver ECC Disabled.
[ 1.360000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
[ 1.370000] NAND_ECC_NONE selected by board driver. This is not recommended !!
[ 1.370000] Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
[ 1.380000] 0x000000000000-0x000000080000 : "Bootloader"
[ 1.390000] mtd: Giving out device 0 to Bootloader
[ 1.390000] 0x000000080000-0x000000580000 : "Kernel"
[ 1.400000] mtd: Giving out device 1 to Kernel
[ 1.400000] 0x000000580000-0x000010000000 : "rootfs"
[ 1.480000] mtd: Giving out device 2 to rootfs
[ 1.480000] mtd: partition "rootfs" set to be root filesystem
[ 1.490000] mtd: partition "rootfs_data" created automatically, ofs=6E0000, len=F920000
[ 1.490000] 0x0000006e0000-0x000010000000 : "rootfs_data"
[ 1.570000] mtd: Giving out device 3 to rootfs_data
[ 1.580000] dm9000 Ethernet Driver, V1.31
[ 1.700000] eth0: dm9000a at d0868000,d0c00004 IRQ 108 MAC: 08:90:90:90:90:90 (chip)
[ 1.700000] mice: PS/2 mouse device common for all mice
[ 1.700000] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[ 1.710000] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 1.720000] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[ 1.720000] i2c /dev entries driver
[ 1.730000] Linux video capture interface: v2.00
[ 1.730000] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 1.740000] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[ 1.740000] cpuidle: using governor ladder
[ 1.750000] sdhci: Secure Digital Host Controller Interface driver
[ 1.750000] sdhci: Copyright(c) Pierre Ossman
[ 1.760000] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000 Hz)
[ 1.760000] s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000 Hz)
[ 1.770000] s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (24000000 Hz)
[ 1.780000] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
[ 1.790000] ALSA device list:
[ 1.790000] No soundcards found.
[ 1.790000] TCP cubic registered
[ 1.790000] NET: Registered protocol family 17
[ 1.800000] s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=80808080
[ 1.810000] NET: Registered protocol family 33
[ 1.810000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 1.810000] All bugs added by David S. Miller <davem@redhat.com>
[ 1.830000] s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-01 08:53:06 UTC (946716786)
[ 1.840000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.840000] Freeing init memory: 112K
awk: /proc/cpuinfo: No such file or directory
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
[ 8.840000] mini_fo: using base directory: /
[ 8.840000] mini_fo: using storage directory: /tmp/root
- init -
Please press Enter to activate this console. [ 10.410000] eth0: link down
[ 12.440000] PPP generic driver version 2.4.2
[ 12.860000] NET: Registered protocol family 24
[ 21.500000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 21.500000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 21.510000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 44.830000] nand_erase_nand: attempt to erase a bad block at page 0x00019200
[ 44.830000] Erase at 0x0c220000 failed immediately: errno -5
[ 101.540000] done.
[ 101.650000] mini_fo: using base directory: /
[ 101.650000] mini_fo: using storage directory: /overlay
[ 101.940000] s3c2410-wdt s3c2410-wdt: timeout 60 too big