主题 : tiny6410 烧写 openwrt 好后不能访问 复制链接 | 浏览器收藏 | 打印
级别: 侠客
UID: 30443
精华: 0
发帖: 85
金钱: 425 两
威望: 85 点
贡献值: 0 点
综合积分: 170 分
注册时间: 2010-10-16
最后登录: 2013-01-08
楼主  发表于: 2011-10-25 21:13

 tiny6410 烧写 openwrt 好后不能访问

tiny6410 烧写 openwrt 好后不能访问,设置好了IP地址,两边都ping 不通
浏览器里直接打开也打不开
不想当厨子的裁缝,不是好司机。
疯狂的嵌入式爱好者
级别: 论坛版主
UID: 40543
精华: 1
发帖: 169
金钱: 920 两
威望: 184 点
贡献值: 1 点
综合积分: 358 分
注册时间: 2011-03-19
最后登录: 2013-05-10
1楼  发表于: 2011-10-26 01:08
能给出串口的启动信息么?
别人转角遇见爱,我转角遇见猫T _T .
级别: 侠客
UID: 30443
精华: 0
发帖: 85
金钱: 425 两
威望: 85 点
贡献值: 0 点
综合积分: 170 分
注册时间: 2010-10-16
最后登录: 2013-01-08
2楼  发表于: 2011-10-26 10:18

 回 1楼(lintel) 的帖子 谢谢lintel哥

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 2.6.36.4 (smbrave@bertrand) (gcc version 4.3.3 (GCC
) ) #1 PREEMPT Sat Oct 22 10:31:43 EDT 2011
[    0.000000] CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr
=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca
che
[    0.000000] Machine: Mini6410
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU S3C6410 (id 0x36410101)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] camera: no parent clock specified
[    0.000000] S3C64XX: PLL settings, A=666000000, M=532000000, E=24000000
[    0.000000] S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
[    0.000000] mout_apll: source is fout_apll (1), rate is 666000000
[    0.000000] mout_epll: source is epll (1), rate is 24000000
[    0.000000] mout_mpll: source is mpll (1), rate is 532000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] mmc_bus: source is mout_epll (0), rate is 24000000
[    0.000000] usb-bus-host: source is clk_48m (0), rate is 48000000
[    0.000000] uclk1: source is dout_mpll (1), rate is 66500000
[    0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[    0.000000] spi-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] audio-bus: source is mout_epll (0), rate is 24000000
[    0.000000] irda-bus: source is mout_epll (0), rate is 24000000
[    0.000000] camera: no parent clock specified
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 65024
[    0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs cons
ole=ttySAC0,115200
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 255260k/255260k available, 6884k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xff600000 - 0xffe00000   (   8 MB)
[    0.000000]     vmalloc : 0xd0800000 - 0xe0000000   ( 248 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc002a000   ( 136 kB)
[    0.000000]       .text : 0xc002a000 - 0xc0420000   (4056 kB)
[    0.000000]       .data : 0xc0420000 - 0xc04466c0   ( 154 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N
odes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU-based detection of stalled CPUs is disabled.
[    0.000000]  Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:246
[    0.000000] VIC @f4000000: id 0x00041192, vendor 0x41
[    0.000000] VIC @f4010000: id 0x00041192, vendor 0x41
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttySAC0] enabled
[    0.020000] Calibrating delay loop... 665.19 BogoMIPS (lpj=3325952)
[    0.260000] pid_max: default: 32768 minimum: 301
[    0.260000] Mount-cache hash table entries: 512
[    0.260000] CPU: Testing write buffer coherency: ok
[    0.270000] NET: Registered protocol family 16
[    0.300000] LEDs initialized.
[    0.300000] s3c64xx_dma_init: Registering DMA channels
[    0.300000] s3c64xx_dma_init1: registering DMA 0 (d0808100)
[    0.310000] s3c64xx_dma_init1: registering DMA 1 (d0808120)
[    0.310000] s3c64xx_dma_init1: registering DMA 2 (d0808140)
[    0.320000] s3c64xx_dma_init1: registering DMA 3 (d0808160)
[    0.320000] s3c64xx_dma_init1: registering DMA 4 (d0808180)
[    0.330000] s3c64xx_dma_init1: registering DMA 5 (d08081a0)
[    0.340000] s3c64xx_dma_init1: registering DMA 6 (d08081c0)
[    0.340000] s3c64xx_dma_init1: registering DMA 7 (d08081e0)
[    0.350000] PL080: IRQ 73, at d0808000
[    0.350000] s3c64xx_dma_init1: registering DMA 8 (d080c100)
[    0.360000] s3c64xx_dma_init1: registering DMA 9 (d080c120)
[    0.360000] s3c64xx_dma_init1: registering DMA 10 (d080c140)
[    0.370000] s3c64xx_dma_init1: registering DMA 11 (d080c160)
[    0.370000] s3c64xx_dma_init1: registering DMA 12 (d080c180)
[    0.380000] s3c64xx_dma_init1: registering DMA 13 (d080c1a0)
[    0.380000] s3c64xx_dma_init1: registering DMA 14 (d080c1c0)
[    0.390000] s3c64xx_dma_init1: registering DMA 15 (d080c1e0)
[    0.400000] PL080: IRQ 74, at d080c000
[    0.400000] S3C6410: Initialising architecture
[    0.460000] bio: create slab <bio-0> at 0
[    0.460000] SCSI subsystem initialized
[    0.460000] usbcore: registered new interface driver usbfs
[    0.460000] usbcore: registered new interface driver hub
[    0.470000] usbcore: registered new device driver usb
[    0.480000] s3c-i2c s3c2440-i2c: slave address 0x10
[    0.480000] s3c-i2c s3c2440-i2c: bus frequency set to 64 KHz
[    0.490000] s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
[    0.490000] Advanced Linux Sound Architecture Driver Version 1.0.23.
[    0.550000] NET: Registered protocol family 2
[    0.550000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.560000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.570000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.570000] TCP: Hash tables configured (established 8192 bind 8192)
[    0.580000] TCP reno registered
[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] NET: Registered protocol family 1
[    0.600000] audit: initializing netlink socket (disabled)
[    0.600000] type=2000 audit(0.600:1): initialized
[    0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.640000] Registering mini_fo version $Id$
[    0.650000] JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (LZO) (LZMA) (RTIME) (R
UBIN) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.660000] msgmni has been set to 498
[    0.660000] io scheduler noop registered (default)
[    0.670000] S3C_LCD clock got enabled :: 133.000 Mhz
[    0.690000] LCD TYPE :: N43 will be initialized
[    0.690000] Window[0] - FB1: map_video_memory: clear ff600000:0013ec00
[    0.700000]             FB1: map_video_memory: dma=5fa00000 cpu=ff600000 size
=0013ec00
[    0.710000] Console: switching to colour frame buffer device 60x17
[    0.710000] fb0: s3cfb frame buffer device
[    0.720000] backlight        initialized
[    1.450000] gpiodev: gpio device registered with major 253
[    1.450000] leds     initialized
[    1.450000] adc      initialized
[    1.450000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.460000] s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is
a S3C6400/10
[    1.470000] s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is
a S3C6400/10
[    1.480000] s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is
a S3C6400/10
[    1.490000] s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is
a S3C6400/10
[    1.500000] S3C NAND Driver, (c) 2008 Samsung Electronics
[    1.500000] S3C NAND Driver ECC Disabled.
[    1.500000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 2
56MiB 3,3V 8-bit)
[    1.510000] NAND_ECC_NONE selected by board driver. This is not recommended !
!
[    1.520000] Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
[    1.520000] 0x000000000000-0x000000080000 : "Bootloader"
[    1.530000] 0x000000080000-0x000000580000 : "Kernel"
[    1.540000] 0x000000580000-0x000010000000 : "rootfs"
[    1.580000] mtd: partition "rootfs" set to be root filesystem
[    1.580000] mtd: partition "rootfs_data" created automatically, ofs=6E0000, l
en=F920000
[    1.590000] 0x0000006e0000-0x000010000000 : "rootfs_data"
[    1.640000] dm9000 Ethernet Driver, V1.31
[    1.760000] eth0: dm9000a at d08da000,d0c00004 IRQ 108 MAC: 08:90:90:90:90:90
(chip)
[    1.760000] mice: PS/2 mouse device common for all mice
[    1.770000] touchscreen-1wire        initialized
[    1.770000] backlight-1wire  initialized
[    1.770000] input: TouchScreen Pipe as /devices/virtual/input/input0
[    1.780000] ts-if    initialized
[    1.780000] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[    1.790000] one_wire_status: 4
[    1.790000] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[    1.800000] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[    1.800000] i2c /dev entries driver
[    1.810000] Linux video capture interface: v2.00
[    1.810000] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[    1.820000] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq e
nabled
[    1.820000] cpuidle: using governor ladder
[    1.830000] one_wire_status: 4
[    1.830000] sdhci: Secure Digital Host Controller Interface driver
[    1.840000] sdhci: Copyright(c) Pierre Ossman
[    1.840000] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
[    1.850000] s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
[    1.850000] s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
[    1.860000] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[    1.870000] one_wire_status: 3
[    1.880000] s3c6400_setup_sdhci_cfg_card: CTRL 2=c0004120, 3=80808080
[    1.880000] specify port
[    1.880000] snd_mpu401: probe of snd_mpu401.0 failed with error -22
[    1.890000] usbcore: registered new interface driver snd-usb-audio
[    1.890000] asoc: AC97 HiFi <-> s3c-ac97 mapping ok
[    2.150000] ALSA device list:
[    2.150000]   #0: MINI6410 (WM9713)
[    2.150000] TCP westwood registered
[    2.150000] NET: Registered protocol family 17
[    2.160000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    2.170000] All bugs added by David S. Miller <davem@redhat.com>
[    2.180000] s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-14 01:29:23
UTC (947813363)
[    2.190000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.190000] Freeing init memory: 136K
- preinit -
timePress the [f] key and hit [enter] to enter failsafe mode

- regular preinit -
timejffs2 not ready yet; using ramdisk
[    9.010000] mini_fo: using base directory: /
[    9.010000] mini_fo: using storage directory: /tmp/root
- init -

Please press Enter to activate this console. [   10.800000] eth0: link down
[   11.170000] device eth0 entered promiscuous mode
[   12.350000] PPP generic driver version 2.4.2
[   12.960000] NET: Registered protocol family 24
[   18.510000] eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
[   18.570000] br-lan: port 1(eth0) entering forwarding state
[   18.570000] br-lan: port 1(eth0) entering forwarding state
[   20.200000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   20.210000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   20.210000] jffs2_build_filesystem(): erasing all blocks after the end marker
...
[   46.500000] nand_erase_nand: attempt to erase a bad block at page 0x00015540
[   46.500000] Erase at 0x0a3c0000 failed immediately: errno -5



BusyBox v1.15.3 (2011-10-22 10:05:57 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
Backfire (10.03.1-RC6, r39) --------------------
  * 1/3 shot Kahlua    In a shot glass, layer Kahlua
  * 1/3 shot Bailey's  on the bottom, then Bailey's,
  * 1/3 shot Vodka     then Vodka.
---------------------------------------------------
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/# [   90.420000] nand_erase_nand: attempt to erase a bad block at
page 0x00002d40
[   90.420000] Erase at 0x00fc0000 failed immediately: errno -5
[   95.120000] done.
[   95.120000] JFFS2 notice: (2143) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0
orphan) found.
[   95.260000] mini_fo: using base directory: /
[   95.260000] mini_fo: using storage directory: /overlay
[   95.580000] s3c2410-wdt s3c2410-wdt: timeout 60 too big

root@OpenWrt:/#
root@OpenWrt:/#
不想当厨子的裁缝,不是好司机。
级别: 侠客
UID: 30443
精华: 0
发帖: 85
金钱: 425 两
威望: 85 点
贡献值: 0 点
综合积分: 170 分
注册时间: 2010-10-16
最后登录: 2013-01-08
3楼  发表于: 2011-10-26 10:26

 回 1楼(lintel) 的帖子

现在访问如图,怎么处理

不想当厨子的裁缝,不是好司机。
疯狂的嵌入式爱好者
级别: 论坛版主
UID: 40543
精华: 1
发帖: 169
金钱: 920 两
威望: 184 点
贡献值: 1 点
综合积分: 358 分
注册时间: 2011-03-19
最后登录: 2013-05-10
4楼  发表于: 2011-10-26 14:42
呃。。。这个是可以访问了,只是你没添加luci的控制界面而已。
别人转角遇见爱,我转角遇见猫T _T .
级别: 侠客
UID: 30443
精华: 0
发帖: 85
金钱: 425 两
威望: 85 点
贡献值: 0 点
综合积分: 170 分
注册时间: 2010-10-16
最后登录: 2013-01-08
5楼  发表于: 2011-10-26 16:05

 回 4楼(lintel) 的帖子

如何填加luci控制界面?小弟不懂
不想当厨子的裁缝,不是好司机。
疯狂的嵌入式爱好者
级别: 论坛版主
UID: 40543
精华: 1
发帖: 169
金钱: 920 两
威望: 184 点
贡献值: 1 点
综合积分: 358 分
注册时间: 2011-03-19
最后登录: 2013-05-10
6楼  发表于: 2011-10-26 17:04
feed更新并安装软件包后,在菜单选择luci,luci-admin-core
别人转角遇见爱,我转角遇见猫T _T .
级别: 侠客
UID: 30443
精华: 0
发帖: 85
金钱: 425 两
威望: 85 点
贡献值: 0 点
综合积分: 170 分
注册时间: 2010-10-16
最后登录: 2013-01-08
7楼  发表于: 2011-10-26 21:55

 回 6楼(lintel) 的帖子

小弟愚钝,能不能说清楚一点。
不想当厨子的裁缝,不是好司机。
疯狂的嵌入式爱好者
级别: 论坛版主
UID: 40543
精华: 1
发帖: 169
金钱: 920 两
威望: 184 点
贡献值: 1 点
综合积分: 358 分
注册时间: 2011-03-19
最后登录: 2013-05-10
8楼  发表于: 2011-10-27 00:53
./script/feed update
./script/feed install -a
make menuconfig
选择LuCI
选择Modules
选择Luci-mod-admin-full
保存
make V=99
别人转角遇见爱,我转角遇见猫T _T .
级别: 新手上路
UID: 35122
精华: 0
发帖: 3
金钱: 15 两
威望: 3 点
贡献值: 0 点
综合积分: 6 分
注册时间: 2010-12-27
最后登录: 2017-09-13
9楼  发表于: 2012-08-28 18:22
uboot启动后,烧写.bin文件吗? 烧到哪个地址呢?