本人新入手一Nanopi3烧写了官网给的Ubuntu和Debian系统都能正常启动，但唯独Android系统启动失败，下面有log，请高手帮忙解决！谢谢！
Nanopi3
16G Kingstong SD
2A 电源
未接LCD
连接了网线
[ 0.336000] CPU7: thread -1, cpu 3, socket 4, mpidr 80040403
[ 0.336000] Brought up 8 CPUs
[ 0.336000] SMP: Total of 8 processors activated (12754.94 BogoMIPS).
[ 0.344000] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 3
[ 0.344000] pwm: max = 50000000 hz
[ 0.344000] prepare_gpio_suspend:
[ 0.344000] alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
[ 0.344000] alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
[ 0.344000] alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
[ 0.344000] alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
[ 0.344000] alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
[ 0.348000] dummy:
[ 0.348000] NET: Registered protocol family 16
[ 0.348000] persistent_ram: uncorrectable error in header
[ 0.348000] persistent_ram: no valid data in buffer (sig = 0xffffffff)
[ 0.360000] console [ram-1] enabled
[ 0.360000] [Register machine platform devices]
[ 0.360000] mach: add amba device pl08xdmac.0
[ 0.360000] mach: add amba device pl08xdmac.1
[ 0.360000] mach: add device uart0
[ 0.360000] mach: add device uart1
[ 0.360000] mach: add device uart3
[ 0.360000] mach: add device uart4
[ 0.364000] mach: add device syncgen [2]
[ 0.364000] mach: add device lcd
[ 0.364000] mach: add device i2c bus (array:3)
[ 0.364000] mach: add device Real Time Clock
[ 0.364000] mach: add device generic pwm (array:4)
[ 0.364000] mach: add device generic gpio (array:6)
[ 0.364000] mach: add device i2s (array:1)
[ 0.364000] mach: add device spdif tx
[ 0.364000] mach: add device usb_ehci
[ 0.364000] mach: add device usb_ohci
[ 0.364000] mach: add device usb otg
[ 0.364000] mach: add device ion-nxp
[ 0.364000] mach: add graphic device opengl|es
[ 0.364000] [Register board platform devices]
[ 0.364000] plat: board revision 7
[ 0.364000] plat: add dynamic frequency (pll.1)
[ 0.364000] plat: add device TMU
[ 0.364000] plat: add framebuffer
[ 0.364000] plat: boot from mmc.0
[ 0.368000] plat: add device sdmmc [0]
[ 0.368000] plat: add device sdmmc [1]
[ 0.368000] plat: add backlight pwm device
[ 0.368000] plat: add device keypad
[ 0.368000] plat: add device spdif playback
[ 0.368000] plat: add device asoc-es8316
[ 0.368000] plat: add device nxp-v4l2
[ 0.372000] plat: register spidev
[ 0.372000] plat: add touch(ft5x0x) device
[ 0.372000] plat: add touch(it7260) device
[ 0.372000] plat: add onewire ts device
[ 0.372000] plat: add device hdmi-cec
[ 0.372000] plat: add device nxp-gmac
[ 0.372000] plat: add device gpio_led
[ 0.372000]
[ 0.372000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.372000] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.396000] bio: create slab <bio-0> at 0
[ 0.396000] gpiochip_add: registered GPIOs 0 to 31 on device: GPIOA
[ 0.396000] gpiochip_add: registered GPIOs 32 to 63 on device: GPIOB
[ 0.396000] gpiochip_add: registered GPIOs 64 to 95 on device: GPIOC
[ 0.396000] gpiochip_add: registered GPIOs 96 to 127 on device: GPIOD
[ 0.400000] gpiochip_add: registered GPIOs 128 to 159 on device: GPIOE
[ 0.400000] gpiochip_add: registered GPIOs 160 to 165 on device: GPIOALV
[ 0.400000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
[ 0.400000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
[ 0.400000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
[ 0.400000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 33
[ 0.400000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
[ 0.400000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
[ 0.400000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
[ 0.404000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 34
[ 0.404000] nxp_ion_probe success!!!
[ 0.404000] SCSI subsystem initialized
[ 0.404000] usbcore: registered new interface driver usbfs
[ 0.404000] usbcore: registered new interface driver hub
[ 0.404000] usbcore: registered new device driver usb
[ 0.404000] i2c-gpio i2c-gpio.3: using pins 159 (SDA) and 158 (SCL)
[ 0.408000] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.408000] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.408000] s3c-i2c s3c2440-i2c.0: bus frequency set to 390 KHz
[ 0.408000] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.408000] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.408000] s3c-i2c s3c2440-i2c.1: bus frequency set to 97 KHz
[ 0.408000] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.412000] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 0.412000] s3c-i2c s3c2440-i2c.2: bus frequency set to 195 KHz
[ 0.412000] Linux media interface: v0.10
[ 0.412000] Linux video capture interface: v2.00
[ 0.412000] pps_core: LinuxPPS API ver. 1 registered
[ 0.412000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <
giometti@linux.it>
[ 0.412000] PTP clock support registered
[ 0.416000] axp_mfd 3-0034: AXP (CHIP ID: 0x06) detected
[ 0.420000] axp22_ldo1: 3000 mV
[ 0.428000] axp22_aldo1: 700 <--> 3300 mV at 3300 mV
[ 0.432000] axp22_aldo2: 700 <--> 3300 mV at 1800 mV
[ 0.436000] axp22_aldo3: 700 <--> 3300 mV at 1000 mV
[ 0.440000] axp22_dldo1: 700 <--> 3300 mV at 3300 mV
[ 0.440000] axp22_dldo2: No configuration
[ 0.444000] axp22_dldo2: 700 <--> 3300 mV at 700 mV
[ 0.444000] axp22_dldo3: No configuration
[ 0.444000] axp22_dldo3: 700 <--> 3300 mV at 700 mV
[ 0.448000] axp22_dldo4: No configuration
[ 0.448000] axp22_dldo4: 700 <--> 3300 mV at 700 mV
[ 0.452000] axp22_eldo1: 700 <--> 3300 mV at 1800 mV
[ 0.460000] axp22_eldo2: 700 <--> 3300 mV at 3300 mV
[ 0.460000] axp22_eldo3: No configuration
[ 0.460000] axp22_eldo3: 700 <--> 3300 mV at 700 mV
[ 0.464000] axp22_dc5ldo: No configuration
[ 0.464000] axp22_dc5ldo: 700 <--> 1400 mV at 1200 mV
[ 0.468000] axp22_dcdc1: 1600 <--> 3400 mV at 3300 mV
[ 0.472000] axp22_dcdc2: 600 <--> 1540 mV at 1200 mV
[ 0.476000] axp22_dcdc3: 600 <--> 1860 mV at 1200 mV
[ 0.480000] axp22_dcdc4: 600 <--> 1540 mV at 1500 mV
[ 0.488000] axp22_dcdc5: 1000 <--> 2550 mV at 1500 mV
[ 0.488000] axp22_ldoio0: 700 <--> 3300 mV at 3800 mV
[ 0.492000] axp22_ldoio1: 700 <--> 3300 mV at 3800 mV
[ 0.492000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.492000] Bluetooth: Core ver 2.16
[ 0.492000] NET: Registered protocol family 31
[ 0.492000] Bluetooth: HCI device and connection manager initialized
[ 0.492000] Bluetooth: HCI socket layer initialized
[ 0.492000] Bluetooth: L2CAP socket layer initialized
[ 0.492000] Bluetooth: SCO socket layer initialized
[ 0.496000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.496000] Switching to clocksource source timer
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[ 0.500000] dummy_timer is not functional.
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Could not switch to high resolution mode on CPU 6
[ 0.500000] Could not switch to high resolution mode on CPU 7
[ 0.500000] Could not switch to high resolution mode on CPU 4
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Could not switch to high resolution mode on CPU 3
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Clockevents: could not switch to one-shot mode:
[ 0.500000] Could not switch to high resolution mode on CPU 2
[ 0.500000] Could not switch to high resolution mode on CPU 0
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Could not switch to high resolution mode on CPU 1
[ 0.500000] dummy_timer is not functional.
[ 0.500000] Could not switch to high resolution mode on CPU 5
[ 0.512000] NET: Registered protocol family 2
[ 0.512000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.516000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.516000] TCP bind hash table entries: 65536 (order: 8, 1572864 bytes)
[ 0.520000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.520000] TCP: reno registered
[ 0.520000] UDP hash table entries: 512 (order: 3, 32768 bytes)
[ 0.520000] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes)
[ 0.520000] NET: Registered protocol family 1
[ 0.520000] RPC: Registered named UNIX socket transport module.
[ 0.520000] RPC: Registered udp transport module.
[ 0.520000] RPC: Registered tcp transport module.
[ 0.520000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.520000] Unpacking initramfs...
[ 0.560000] Initramfs unpacking failed: junk in compressed archive
[ 0.560000] Freeing initrd memory: 1024K
[ 0.560000] Disply Reset Status : On
[ 0.560000] Display LCD register operation
[ 0.560000] Display.0 fps=45 (22 ms), wait= 8 jiffies, Pixelclk=43885285hz
[ 0.564000] LCD : [1]=LCD connect to [6]=SYNCGEN0
[ 0.564000] bt_bcm: rfkill initialized
[ 0.564000] audit: initializing netlink socket (disabled)
[ 0.564000] type=2000 audit(0.560:1): initialized
[ 0.564000] highmem bounce pool size: 64 pages
[ 0.576000] NFS: Registering the id_resolver key type
[ 0.576000] fuse init (API version 7.18)
[ 0.576000] msgmni has been set to 1151
[ 0.576000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.576000] io scheduler noop registered
[ 0.576000] io scheduler deadline registered
[ 0.576000] io scheduler cfq registered (default)
[ 0.580000] display.0 connected to fb.0 ...
[ 0.580000] nxp-fb.0: dma addr = 0x65600000, buf[0xe4a15100]
[ 0.580000] nxp-fb.0: dma addr = 0x65984000, buf[0xe4a152c0]
[ 0.580000] nxp-fb.0: dma addr = 0x65d08000, buf[0xe4a15480]
[ 0.664000] nxp-fb 0: out[0], 1280 * 720 - 32 bpp (phys:65600000 virt:0xe5600000 max:11059200)
[ 0.664000] nxp-uart.0: ttySAC0 at MMIO 0xc00a1000 (irq = 39) is a S3C6400/10
[ 2.084000] console [ttySAC0] enabled
[ 2.088000] nxp-uart.1: ttySAC1 at MMIO 0xc00a0000 (irq = 38) is a S3C6400/10
[ 2.096000] nxp-uart.3: ttySAC3 at MMIO 0xc00a3000 (irq = 41) is a S3C6400/10
[ 2.104000] nxp-uart.4: ttySAC4 at MMIO 0xc006d000 (irq = 42) is a S3C6400/10
[ 2.116000] loop: module loaded
[ 2.116000] tun: Universal TUN/TAP device driver, 1.6
[ 2.120000] tun: (C) 1999-2004 Max Krasnyansky <
maxk@qualcomm.com>
[ 2.124000] -- nxpmac initialize --
[ 2.128000] stmmac - user ID: 0x37, Synopsys ID: 0x37
[ 2.132000] Ring mode enabled
[ 2.136000] DMA HW capability register supported
[ 2.140000] Enhanced/Alternate descriptors
[ 2.144000] Enabled extended descriptors
[ 2.148000] RX Checksum Offload Engine supported (type 2)
[ 2.156000] TX Checksum insertion supported
[ 2.160000] Wake-Up On Lan supported
[ 2.164000] Enable RX Mitigation via HW Watchdog Timer
[ 2.204000] stmmac: probed
[ 2.204000] eth0: PHY ID 001cc915 at 0 IRQ 257 (stmmac-0:00)
[ 2.208000] eth0: PHY ID 001cc915 at 7 IRQ 257 (stmmac-0:07) active
[ 2.216000] PPP generic driver version 2.4.2
[ 2.220000] PPP BSD Compression module registered
[ 2.224000] PPP Deflate Compression module registered
[ 2.228000] PPP MPPE Compression module registered
[ 2.232000] NET: Registered protocol family 24
[ 2.236000] usbcore: registered new interface driver asix
[ 2.244000] usbcore: registered new interface driver cdc_ether
[ 2.248000] usbcore: registered new interface driver net1080
[ 2.252000] usbcore: registered new interface driver cdc_subset
[ 2.260000] usbcore: registered new interface driver zaurus
[ 2.264000] usbcore: registered new interface driver cdc_ncm
[ 2.272000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.276000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
[ 2.284000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
[ 2.292000] nxp-ehci nxp-ehci: irq 82, io mem 0xc0030000
[ 2.308000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
[ 2.308000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.312000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.320000] usb usb1: Product: SLsi Synopsys EHCI Host Controller
[ 2.324000] usb usb1: Manufacturer: Linux 3.4.39-FriendlyARM ehci_hcd
[ 2.332000] usb usb1: SerialNumber: nxp-ehci
[ 2.336000] hub 1-0:1.0: USB hub found
[ 2.340000] hub 1-0:1.0: 3 ports detected
[ 2.344000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 2.552000] Core Release: 2.93a
[ 2.552000] Setting default values for core params
[ 2.552000] Finished setting default values for core params
[ 2.668000] usb 1-1: new high-speed USB device number 2 using nxp-ehci
[ 2.756000] Using Buffer DMA mode
[ 2.760000] Dedicated Tx FIFOs mode
[ 2.760000] dwc_otg dwc_otg: DWC OTG Controller
[ 2.764000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
[ 2.772000] dwc_otg dwc_otg: irq 81, io mem 0x00000000
[ 2.776000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.784000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.788000] usb usb2: Product: DWC OTG Controller
[ 2.796000] usb usb2: Manufacturer: Linux 3.4.39-FriendlyARM dwc_otg_hcd
[ 2.800000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610
[ 2.800000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.800000] usb 1-1: Product: USB2.0 Hub
[ 2.800000] hub 1-1:1.0: USB hub found
[ 2.800000] hub 1-1:1.0: 4 ports detected
[ 2.828000] usb usb2: SerialNumber: dwc_otg
[ 2.832000] hub 2-0:1.0: USB hub found
[ 2.836000] hub 2-0:1.0: 1 port detected
[ 2.840000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.844000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
[ 2.852000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
[ 2.856000] nxp-ohci nxp-ohci: irq 82, io mem 0xc0020000
[ 2.924000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.924000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.932000] usb usb3: Product: SLsi Synopsys OHCI Host Controller
[ 2.936000] usb usb3: Manufacturer: Linux 3.4.39-FriendlyARM ohci_hcd
[ 2.944000] usb usb3: SerialNumber: nxp-ohci
[ 2.948000] hub 3-0:1.0: USB hub found
[ 2.952000] hub 3-0:1.0: 3 ports detected
[ 2.956000] Initializing USB Mass Storage driver...
[ 2.960000] usbcore: registered new interface driver usb-storage
[ 2.964000] USB Mass Storage support registered.
[ 2.972000] usbcore: registered new interface driver usbserial
[ 2.976000] usbcore: registered new interface driver usbserial_generic
[ 2.984000] USB Serial support registered for generic
[ 2.988000] usbserial: USB Serial Driver core
[ 2.992000] usbcore: registered new interface driver ch341
[ 2.996000] USB Serial support registered for ch341-uart
[ 3.004000] usbcore: registered new interface driver cp210x
[ 3.008000] USB Serial support registered for cp210x
[ 3.012000] usbcore: registered new interface driver ftdi_sio
[ 3.020000] USB Serial support registered for FTDI USB Serial Device
[ 3.024000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 3.032000] usbcore: registered new interface driver option
[ 3.036000] USB Serial support registered for GSM modem (1-port)
[ 3.044000] usbcore: registered new interface driver pl2303
[ 3.048000] USB Serial support registered for pl2303
[ 3.052000] usbcore: registered new interface driver ti_usb_3410_5052
[ 3.060000] USB Serial support registered for TI USB 3410 1 port adapter
[ 3.068000] USB Serial support registered for TI USB 5052 2 port adapter
[ 3.072000] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
[ 3.080000] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 3.088000] android_usb gadget: Number of LUNs=1
[ 3.092000] lun0: LUN: removable file: (no medium)
[ 3.096000] android_usb gadget: android_usb ready
[ 3.100000] mousedev: PS/2 mouse device common for all mice
[ 3.108000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
[ 3.112000] usbcore: registered new interface driver xpad
[ 3.120000] i2c-core: driver [IT7260-ts] using legacy suspend method
[ 3.124000] i2c-core: driver [IT7260-ts] using legacy resume method
[ 3.132000] touchscreen-1wire initialized
[ 3.136000] backlight-1wire initialized
[ 3.140000] input: fa_ts_input as /devices/virtual/input/input1
[ 3.144000] ts-if initialized
[ 3.148000] [RTC] day=2016.01.01 time=08:00:00
[ 3.152000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
[ 3.160000] i2c /dev entries driver
[ 3.164000] ...................................ov5640_probe 2234
[ 3.168000] ...................................ov5640_video_probe 2193
[ 3.176000] i2c-nxp.0: ack was not received
[ 3.180000] i2c->nxp.0: incomplete xfer (-6)
[ 3.184000] ov5640 0-003c: reg_read: i2c read error, reg: 300a
[ 3.188000] OV5640 read error!!!!!!!!!!!!!!!
[ 3.192000] ov5640_initialize_ctrls.............1794...........
[ 3.200000] nxp_hdmi_cec_probe success
[ 3.204000] device-mapper: uevent: version 1.0.3
[ 3.208000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised:
dm-devel@redhat.com[ 3.216000] Bluetooth: HCI UART driver ver 2.2
[ 3.220000] Bluetooth: HCI H4 protocol initialized
[ 3.224000] DVFS: ASV[3] IDS 18mA, Ro 137 -> Table [IDS 38mA, Ro 170]
[ 3.232000] DVFS: regulator vdd_arm_1.3V
[ 3.236000] DVFS: cpu DVFS with PLL.1 [tables=11]
[ 3.240000] cpuidle: using governor ladder
[ 3.244000] cpuidle: using governor menu
[ 3.248000] Synopsys Designware Multimedia Card Interface Driver
[ 3.252000] dw_mmc dw_mmc.0: Using internal DMA controller.
[ 3.260000] mmc0: no vmmc regulator found
[ 3.264000] dw_mmc dw_mmc.0: Using external card detect irq 267 (io 161)
[ 3.272000] dw_mmc dw_mmc.0: Version ID is 250a
[ 3.276000] dw_mmc dw_mmc.0: DW MMC controller at irq 75, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[ 3.284000] dw_mmc dw_mmc.1: Using internal DMA controller.
[ 3.288000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 3.300000] mmc1: no vmmc regulator found
[ 3.304000] dw_mmc dw_mmc.1: Version ID is 250a
[ 3.308000] dw_mmc dw_mmc.1: DW MMC controller at irq 76, 32 bit host data width, 32 deep fifo hw timeout 500 ms
[ 3.320000] usbcore: registered new interface driver usbhid
[ 3.324000] usbhid: USB HID core driver
[ 3.328000] ashmem: initialized
[ 3.332000] logger: created 256K log 'log_main'
[ 3.336000] logger: created 256K log 'log_events'
[ 3.340000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 25000000Hz, actual 25000000HZ div = 1)
[ 3.340000] mmc0: new SDHC card at address 0001
[ 3.340000] mmcblk0: mmc0:0001 00000 14.8 GiB
[ 3.344000] mmcblk0: p1 p2 p3 p4 < p5 p6 p7 >
[ 3.360000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[ 3.372000] logger: created 256K log 'log_radio'
[ 3.376000] logger: created 256K log 'log_system'
[ 3.384000] snd pcm: register sound platform 'nxp-pcm'
[ 3.388000] snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287880hz, RFS=256
[ 3.404000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 300000Hz, actual 297619HZ div = 84)
[ 3.452000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 200000Hz, actual 200000HZ div = 125)
[ 3.512000] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 100000Hz, actual 100000HZ div = 250)
[ 3.512000] asoc: ES8316 HiFi <-> nxp-i2s.0 mapping ok
[ 3.512000] spdif-tx: 48000(47999)Hz, MCLK=12287880hz HDMI out
[ 3.516000] asoc: dit-hifi <-> nxp-spdif-tx mapping ok
[ 3.516000] GACT probability NOT on
[ 3.516000] Mirror/redirect action on
[ 3.516000] u32 classifier
[ 3.516000] Actions configured
[ 3.516000] Netfilter messages via NETLINK v0.30.
[ 3.516000] nf_conntrack version 0.5.0 (13471 buckets, 53884 max)
[ 3.520000] ctnetlink v0.93: registering with nfnetlink.
[ 3.520000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.520000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.520000] xt_time: kernel timezone is -0000
[ 3.520000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.520000] arp_tables: (C) 2002 David S. Miller
[ 3.520000] TCP: cubic registered
[ 3.520000] Initializing XFRM netlink socket
[ 3.520000] NET: Registered protocol family 10
[ 3.524000] Mobile IPv6
[ 3.524000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.524000] IPv6 over IPv4 tunneling driver
[ 3.524000] NET: Registered protocol family 17
[ 3.524000] NET: Registered protocol family 15
[ 3.524000] Bluetooth: RFCOMM TTY layer initialized
[ 3.524000] Bluetooth: RFCOMM socket layer initialized
[ 3.524000] Bluetooth: RFCOMM ver 1.11
[ 3.524000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.524000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.528000] NET: Registered protocol family 35
[ 3.528000] Registering the dns_resolver key type
[ 3.528000] Registering SWP/SWPB emulation handler
[ 3.532000] axp22_dcdc5: incomplete constraints, leaving on
[ 3.532000] axp22_dcdc4: incomplete constraints, leaving on
[ 3.536000] axp22_dcdc3: incomplete constraints, leaving on
[ 3.536000] axp22_dcdc2: incomplete constraints, leaving on
[ 3.536000] axp22_dcdc1: incomplete constraints, leaving on
[ 3.540000] axp22_dc5ldo: incomplete constraints, leaving on
[ 3.540000] axp22_eldo2: incomplete constraints, leaving on
[ 3.540000] axp22_eldo1: incomplete constraints, leaving on
[ 3.548000] axp22_dldo1: incomplete constraints, leaving on
[ 3.548000] axp22_a incomplete constraints, leaving on
[ 3.548000] axp22_aldo2: incomplete constraints, leaving on
[ 3.552000] axp22_aldo1: incomplete constraints, leaving on
[ 3.552000] axp22_ldo1: incomplete constraints, lving on
[ 3.552000] otg_wakelock_init: No USB transceiver found
[ 3.736000] nxp-rtc nxp-rtc.0: setting system clock to 2016-01-01 08:00:00 UTC (1451635200)
[ 3.744000] tmu[0] = trim 40:0, ret 1
[ 3.748000] TMU: register tmu.0 to hwmon (max 1400000khz)
[ 3.752000] ALSA device list:
[ 3.756000] #0: I2S-ES8316
[ 3.760000] #1: SPDIF-Transciever
[ 3.764000] Freeing init memory: 220K
[ 3.764000] Write protecting the kernel text section c0008000 - c081a000
[ 3.772000] rodata_test: attempting to write to read-only section:
[ 3.780000] write to read-only section trapped, success
[ 3.884000] type=1403 audit(1451635200.828:2): policy loaded auid=4294967295 ses=4294967295
[ 3.896000] type=1404 audit(1451635200.840:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[ 4.156000] init: /dev/hw_random not found
[ 4.200000] HDMI HPD State 0x0
[ 4.268000] init: /dev/hw_random not found
[ 4.292000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.296000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.0/by-num/p2,target=/system,type=ext4)=0
[ 4.340000] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.344000] fs_mgr: check_fs(): mount(/dev/block/platform/dw_mmc.0/by-num/p3,/cache,ext4)=0
[ 4.408000] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/dw_mmc.0/by-num/p3
[ 4.616000] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 4.616000] e2fsck: cache: clean, 11/27392 files, 3534/109568 blocks
[ 4.652000] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 4.656000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.0/by-num/p3,target=/cache,type=ext4)=0
[ 4.708000] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
[ 4.712000] fs_mgr: check_fs(): mount(/dev/block/platform/dw_mmc.0/by-num/p7,/data,ext4)=0
[ 4.764000] fs_mgr: Running /system/bin/e2fsck on /dev/block/platform/dw_mmc.0/by-num/p7
[ 4.864000] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
[ 4.864000] e2fsck: userdata: clean, 14/872960 files, 65763/3573760 blocks
[ 4.904000] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 4.908000] fs_mgr: __mount(source=/dev/block/platform/dw_mmc.0/by-num/p7,target=/data,type=ext4)=0
[ 4.944000] setting PHY_BASEADDR_POWER_GATE, set 1
[ 4.944000] setting PHY_BASEADDR_PMU_ISOLATE+4, set 0
[ 4.948000] setting PHY_BASEADDR_PMU_ISOLATE+8, set 0
[ 4.956000] setting PHY_BASEADDR_PMU_ISOLATE, set 1
[ 4.960000] read PHY_BASEADDR_PMU_ISOLATExC
[ 4.964000] Wait Power UP Ack(powerUpAck=0x00000000)
[ 4.968000] setting ClockGen, set 1
[ 4.972000] setting Reset VR addr(0xf0012008)
[ 4.976000] setting PHY_BASEADDR_VR_PMU addr(0xf0072000)
[ 4.984000] Vr: VR device driver loaded(ver1.2) for s5p6818
[ 5.132000] binder: 123:123 transaction failed 29189, size 0-0
[ 5.252000] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
[ 5.252000] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
[ 5.264000] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
[ 5.272000] android_usb: already disabled
[ 5.284000] adb_open
[ 5.284000] mtp_bind_config
[ 5.284000] adb_bind_config
[ 5.776000] logd.auditd: start
shell@nanopi3:/ $ [ 6.140000] healthd: No charger supplies found
[ 6.140000] healthd: No battery devices found
[ 7.716000] ov5640_link_setup
[ 7.720000] camera_common_vin_setup_io
[ 7.720000] i2c-nxp.0: ack was not received
[ 7.724000] i2c->nxp.0: incomplete xfer (-6)
[ 7.728000] ov5640 0-003c: reg_write: i2c write error, reg: 3103
[ 7.732000] ov5640_init: failed to ov5640_write_array init regs
[ 7.740000] ov5640_s_power.............1944...........
[ 7.744000] nxp_hdmi_link_setup: connected to me!!!
[ 29.772000] warning: `main' uses 32-bit capabilities (legacy support in use)
[ 56.480000] healthd: battery none chg=
[ 57.812000] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
[ 57.816000] lowmemorykiller: oom_adj 0 => oom_score_adj 0
[ 57.820000] lowmemorykiller: oom_adj 1 => oom_score_adj 58
[ 57.824000] lowmemorykiller: oom_adj 2 => oom_score_adj 117
[ 57.832000] lowmemorykiller: oom_adj 3 => oom_score_adj 176
[ 57.836000] lowmemorykiller: oom_adj 9 => oom_score_adj 529
[ 57.840000] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
[ 114.044000] acc_open
[ 114.044000] acc_release
[ 150.296000] binder: 1248:1270 refcount change on invalid ref 17
[ 163.768000] bt_bcm: rfkill set_block Off GPIOB.8
[ 163.840000] bt_bcm: rfkill set_block On GPIOB.8
[ 166.760000] bt_bcm: rfkill set_block Off GPIOB.8
[ 207.116000] binder: 406:406 transaction failed 29189, size 108-0
shell@nanopi3:/ $
shell@nanopi3:/ $
