主题 : 烧写完自己编译的system.img之后mmc好像挂掉了,无法再烧其它系统 复制链接 | 浏览器收藏 | 打印
级别: 新手上路
UID: 122986
精华: 0
发帖: 15
金钱: 75 两
威望: 15 点
贡献值: 0 点
综合积分: 30 分
注册时间: 2016-02-26
最后登录: 2020-02-23
楼主  发表于: 43天前

 烧写完自己编译的system.img之后mmc好像挂掉了,无法再烧其它系统

android系统
    android系统中加了/system/lib/hw/led.default.so
现象:
   烧写完自己编译的system.img启动之后一直打印下面内容:
[  117.684121] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[  117.684299] mmcblk0: command error, retrying timeout
系统卡在android几个字,一直进不去,删除rm /system/lib/hw/led.default.so之后,android就可以正常进去了。


问题:
   现在使用MiniTools,sd卡都无法成功烧写新的android系统。
   烧写android系统时:
          显示可以烧写成功,启动之后还是原来的系统。初步推测,虽然minitools,sd卡显示烧写完成,但是其实没有烧写进去。
   烧写QT和Ubuntu时直接报失败:
          Installing fs-image... part system not found Installing fs-image failed
    uboot烧写失败:
           串口输fastboot,然后cmd烧写zImage,ramdisk-img,system.img时,显示成功,但是结果和minitools,sd卡一样,启动之后还是原来系统。
求助:
   如何重新烧写系统,minitools,sd卡,uboot都不行。
   现在有一个想法是使用uboot把emmc全部擦除掉,如果能擦除掉的话应该可以,但是不知道怎么全部擦除,知道的麻烦回复下,在此谢谢了!
   或者如果还有其它方法,麻烦推荐一下,我多试试。




附上开机log:
   [    2.157220]  r8:c02c804c r7:db8f5440 r6:c078d498 r5:00000000 r4:c0924c48
[    2.163719] r3:c02f0e08
[    2.166328] [<c02f1520>] (__class_create+0x0/0x90) from [<c02c80a0>] (leds_init+0x54/0x7c)
[    2.174580]  r7:00000000 r6:db842000 r5:c078d498 r4:c0924c40
[    2.180215] [<c02c804c>] (leds_init+0x0/0x7c) from [<c0044808>] (do_one_initcall+0x38/0x17c)
[    2.188641]  r5:c08db640 r4:c0039268
[    2.192193] [<c00447d0>] (do_one_initcall+0x0/0x17c) from [<c0008a80>] (kernel_init+0xa4/0x150)
[    2.200885] [<c00089dc>] (kernel_init+0x0/0x150) from [<c0089068>] (do_exit+0x0/0x78c)
[    2.208779]  r5:c00089dc r4:00000000
[    2.212490] leds     initialized
[    2.215326] pwm      initialized
[    2.218075] backlight        initialized
[    2.221423] tiny4412-adc     initialized
[    2.225068] Mali: ::Q::exynos_result_of_asv : 0
[    2.229339] Mali: mali_dvfs[0].vol = 950000
[    2.233593] Mali: mali_dvfs[1].vol = 975000
[    2.237846] Mali: mali_runtime_resume.vol = 975000
[    2.242715] Mali: mali_dvfs[2].vol = 1050000
[    2.247055] Mali: mali_dvfs[3].vol = 1100000
[    2.251395] Mali: init_gpu_vol = 1100000
[    2.255853] Mali: init_mali_clock mali_clock c084b5d0
[    2.262980] Mali: Mali device driver loaded
[    2.264797] UMP: UMP device driver r4p0-00rel0-Emerald loaded
[    2.275509] brd: module loaded
[    2.278117] loop: module loaded
[    2.280173] PPP generic driver version 2.4.2
[    2.280924] PPP Deflate Compression module registered
[    2.285771] PPP BSD Compression module registered
[    2.290941] PPP MPPE Compression module registered
[    2.295233] NET: Registered protocol family 24
[    2.299650] tun: Universal TUN/TAP device driver, 1.6
[    2.304692] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.310993] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[    2.318442] usbcore: registered new interface driver pegasus
[    2.324052] usbcore: registered new interface driver asix
[    2.329431] usbcore: registered new interface driver cdc_ether
[    2.335248] usbcore: registered new interface driver dm9620
[    2.340802] usbcore: registered new interface driver net1080
[    2.346441] usbcore: registered new interface driver cdc_subset
[    2.352345] usbcore: registered new interface driver zaurus
[    2.357824] cdc_ncm: 04-Aug-2011
[    2.361111] usbcore: registered new interface driver cdc_ncm
[    2.366865] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.373287] s5p-ehci s5p-ehci: usb phy usage(2)
[    2.377864] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[    2.382988] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[    2.391039] s5p-ehci s5p-ehci: irq 134, io mem 0x12580000
[    2.405036] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[    2.405182] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.407455] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.414670] usb usb1: Product: S5P EHCI Host Controller
[    2.419876] usb usb1: Manufacturer: Linux 3.0.86-FriendlyARM ehci_hcd
[    2.426302] usb usb1: SerialNumber: s5p-ehci
[    2.431000] hub 1-0:1.0: USB hub found
[    2.434282] hub 1-0:1.0: 3 ports detected
[    2.438652] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.444539] s5p-ohci s5p-ohci: usb phy usage(6)
[    2.448957] s5p-ohci s5p-ohci: Already power on PHY
[    2.453839] s5p-ohci s5p-ohci: s5p OHCI
[    2.457658] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
[    2.465100] s5p-ohci s5p-ohci: irq 134, io mem 0x12590000
[    2.529192] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.529264] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.529340] usb usb2: Product: s5p OHCI
[    2.529382] usb usb2: Manufacturer: Linux 3.0.86-FriendlyARM ohci_hcd
[    2.531121] usb usb2: SerialNumber: s5p-ohci
[    2.535841] hub 2-0:1.0: USB hub found
[    2.539101] hub 2-0:1.0: 3 ports detected
[    2.543580] usbcore: registered new interface driver usblp
[    2.548567] Initializing USB Mass Storage driver...
[    2.553541] usbcore: registered new interface driver usb-storage
[    2.559416] USB Mass Storage support registered.
[    2.564224] usbcore: registered new interface driver usbserial
[    2.569918] USB Serial support registered for generic
[    2.574966] usbcore: registered new interface driver usbserial_generic
[    2.581377] usbserial: USB Serial Driver core
[    2.585797] USB Serial support registered for aircable
[    2.590936] usbcore: registered new interface driver aircable
[    2.596650] USB Serial support registered for ark3116
[    2.601698] usbcore: registered new interface driver ark3116
[    2.607243] ark3116:v0.7:USB ARK3116 serial/IrDA driver
[    2.612531] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[    2.620794] usbcore: registered new interface driver belkin
[    2.626252] belkin_sa: v1.3:USB Belkin Serial converter driver
[    2.632139] USB Serial support registered for ch341-uart
[    2.637473] usbcore: registered new interface driver ch341
[    2.642937] USB Serial support registered for cp210x
[    2.647883] usbcore: registered new interface driver cp210x
[    2.653334] cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
[    2.660194] USB Serial support registered for Reiner SCT Cyberjack USB card reader
[    2.667755] usbcore: registered new interface driver cyberjack
[    2.673471] cyberjack: v1.01 Matthias Bruestle
[    2.677896] cyberjack: REINER SCT cyberJack pinpad/e-com USB Chipcard Reader Driver
[    2.685622] USB Serial support registered for DeLorme Earthmate USB
[    2.691869] USB Serial support registered for HID->COM RS232 Adapter
[    2.698204] USB Serial support registered for Nokia CA-42 V2 Adapter
[    2.704558] usbcore: registered new interface driver cypress
[    2.710101] cypress_m8: v1.10:Cypress USB to Serial Driver
[    2.715650] USB Serial support registered for Digi 2 port USB adapter
[    2.722073] USB Serial support registered for Digi 4 port USB adapter
[    2.728515] usbcore: registered new interface driver digi_acceleport
[    2.734752] digi_acceleport: v1.80.1.2:Digi AccelePort USB-2/USB-4 Serial Converter driver
[    2.743081] USB Serial support registered for Edgeport 2 port adapter
[    2.745032] usb 1-2: new high speed USB device number 2 using s5p-ehci
[    2.756041] USB Serial support registered for Edgeport 4 port adapter
[    2.762431] USB Serial support registered for Edgeport 8 port adapter
[    2.768856] USB Serial support registered for EPiC device
[    2.774267] usbcore: registered new interface driver io_edgeport
[    2.780149] io_edgeport: v2.7:Edgeport USB Serial Driver
[    2.785526] USB Serial support registered for Edgeport TI 1 port adapter
[    2.792216] USB Serial support registered for Edgeport TI 2 port adapter
[    2.798908] usbcore: registered new interface driver io_ti
[    2.804279] io_ti: v0.7mode043006:Edgeport USB Serial Driver
[    2.810002] USB Serial support registered for empeg
[    2.814883] usbcore: registered new interface driver empeg
[    2.820250] empeg: v1.3:USB Empeg Mark I/II Driver
[    2.825110] USB Serial support registered for FTDI USB Serial Device
[    2.831497] usbcore: registered new interface driver ftdi_sio
[    2.837089] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[    2.842989] USB Serial support registered for funsoft
[    2.848039] usbcore: registered new interface driver funsoft
[    2.853666] USB Serial support registered for Garmin GPS usb/tty
[    2.859669] usbcore: registered new interface driver garmin_gps
[    2.865486] garmin_gps: v0.36:garmin gps driver
[    2.870068] USB Serial support registered for hp4X
[    2.874839] usbcore: registered new interface driver hp4X
[    2.880143] hp4x: v1.00:HP4x (48/49) Generic Serial driver
[    2.885718] USB Serial support registered for PocketPC PDA
[    2.891105] usb 1-2: New USB device found, idVendor=0424, idProduct=4604
[    2.891228] usbcore: registered new interface driver ipaq
[    2.891233] ipaq: v1.0:USB PocketPC PDA driver
[    2.891323] USB Serial support registered for IPWireless converter
[    2.891430] usbcore: registered new interface driver ipwtty
[    2.891434] ipw: v0.4:IPWireless tty driver
[    2.891520] USB Serial support registered for IR Dongle
[    2.891626] usbcore: registered new interface driver ir-usb
[    2.891631] ir_usb: v0.5:USB IR Dongle driver
[    2.891717] USB Serial support registered for iuu_phoenix
[    2.891820] usbcore: registered new interface driver iuu_phoenix
[    2.891825] iuu_phoenix: v0.12:Infinity USB Unlimited Phoenix driver
[    2.891917] USB Serial support registered for Keyspan - (without firmware)
[    2.892007] USB Serial support registered for Keyspan 1 port adapter
[    2.892097] USB Serial support registered for Keyspan 2 port adapter
[    2.892188] USB Serial support registered for Keyspan 4 port adapter
[    2.892299] usbcore: registered new interface driver keyspan
[    2.892303] keyspan: v1.1.5:Keyspan USB to Serial Converter Driver
[    2.892394] USB Serial support registered for Keyspan PDA
[    2.892485] USB Serial support registered for Keyspan PDA - (prerenumeration)
[    2.892588] USB Serial support registered for Xircom / Entregra PGS - (prerenumeration)
[    2.892699] usbcore: registered new interface driver keyspan_pda
[    2.892704] keyspan_pda: v1.1:USB Keyspan PDA Converter driver
[    2.892793] USB Serial support registered for KL5KUSB105D / PalmConnect
[    2.892902] usbcore: registered new interface driver kl5kusb105d
[    2.892907] kl5kusb105: v0.4:KLSI KL5KUSB105 chipset USB->Serial Converter driver
[    2.893001] USB Serial support registered for KOBIL USB smart card terminal
[    2.893111] usbcore: registered new interface driver kobil
[    2.893116] kobil_sct: 21/05/2004:KOBIL USB Smart Card Terminal Driver (experimental)
[    2.893209] USB Serial support registered for MCT U232
[    2.893321] usbcore: registered new interface driver mct_u232
[    2.893325] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver
[    2.893421] USB Serial support registered for Moschip 2 port adapter
[    2.893426] mos7720: 2.1:Moschip USB Serial Driver
[    2.893534] usbcore: registered new interface driver moschip7720
[    2.893628] USB Serial support registered for Moschip 7840/7820 USB Serial Driver
[    2.893633] mos7840: 1.3.2:Moschip 7840/7820 USB Serial Driver
[    2.893747] usbcore: registered new interface driver mos7840
[    2.893842] USB Serial support registered for moto-modem
[    2.893954] usbcore: registered new interface driver moto-modem
[    2.894059] USB Serial support registered for navman
[    2.894191] usbcore: registered new interface driver navman
[    2.894295] USB Serial support registered for ZyXEL - omni.net lcd plus usb
[    2.894405] usbcore: registered new interface driver omninet
[    2.894410] omninet: v1.1:USB ZyXEL omni.net LCD PLUS Driver
[    2.894501] USB Serial support registered for opticon
[    2.894622] usbcore: registered new interface driver opticon
[    2.894715] USB Serial support registered for GSM modem (1-port)
[    2.894852] usbcore: registered new interface driver option
[    2.894857] option: v0.7.2:USB Driver for GSM modems
[    2.894948] USB Serial support registered for oti6858
[    2.895081] usbcore: registered new interface driver oti6858
[    2.895164] USB Serial support registered for pl2303
[    2.895265] usbcore: registered new interface driver pl2303
[    2.895269] pl2303: Prolific PL2303 USB to serial adaptor driver
[    2.895351] USB Serial support registered for qcaux
[    2.895451] usbcore: registered new interface driver qcaux
[    2.895533] USB Serial support registered for Qualcomm USB modem
[    2.895641] usbcore: registered new interface driver qcserial
[    2.895646] safe_serial: v0.1:USB Safe Encapsulated Serial
[    2.895728] USB Serial support registered for safe_serial
[    2.895827] usbcore: registered new interface driver safe_serial
[    2.895911] USB Serial support registered for siemens_mpi
[    2.896012] usbcore: registered new interface driver siemens_mpi
[    2.896017] Driver for Siemens USB/MPI adapter
[    2.896021] Version 0.1 09/26/2005 Thomas Hergenhahn@web.de http://libnodave.sf.net
[    2.896103] USB Serial support registered for Sierra USB modem
[    2.896203] usbcore: registered new interface driver sierra
[    2.896208] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[    2.896291] USB Serial support registered for SPCP8x5
[    2.896395] usbcore: registered new interface driver spcp8x5
[    2.896399] spcp8x5: v0.10:SPCP8x5 USB to serial adaptor driver
[    2.896484] USB Serial support registered for Quatech SSU-100 USB to Serial Driver
[    2.896583] usbcore: registered new interface driver ssu100
[    2.896587] ssu100: v0.1:Quatech SSU-100 USB to Serial Driver
[    2.896669] USB Serial support registered for symbol
[    2.896775] usbcore: registered new interface driver symbol
[    2.896867] USB Serial support registered for TI USB 3410 1 port adapter
[    2.896951] USB Serial support registered for TI USB 5052 2 port adapter
[    2.897048] usbcore: registered new interface driver ti_usb_3410_5052
[    2.897052] ti_usb_3410_5052: v0.10:TI USB 3410/5052 Serial Driver
[    2.897138] USB Serial support registered for Handspring Visor / Palm OS
[    2.897226] USB Serial support registered for Sony Clie 3.5
[    2.897308] USB Serial support registered for Sony Clie 5.0
[    2.897411] usbcore: registered new interface driver visor
[    2.897415] visor: USB HandSpring Visor / Palm OS driver
[    2.897498] USB Serial support registered for Connect Tech - WhiteHEAT - (prerenumeration)
[    2.897585] USB Serial support registered for Connect Tech - WhiteHEAT
[    2.897691] usbcore: registered new interface driver whiteheat
[    2.897695] whiteheat: v2.0:USB ConnectTech WhiteHEAT driver
[    2.897779] USB Serial support registered for vivopay-serial
[    2.897876] usbcore: registered new interface driver vivopay-serial
[    2.897881] vivopay_serial: v1.0:ViVOpay USB Serial Driver
[    2.897964] USB Serial support registered for zio
[    2.898064] usbcore: registered new interface driver zio
[    2.898149] USB Serial support registered for qc_csvt
[    2.898249] usbcore: registered new interface driver qc_csvt
[    3.459793] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.467319] s3c-udc : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Electronics
[    3.467324] s3c-udc : version 15 March 2009
[    3.478923] hub 1-2:1.0: USB hub found
[    3.480872] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    3.480878] android_usb gadget: Number of LUNs=1
[    3.480884]  lun0: LUN: removable file: (no medium)
[    3.481475] android_usb gadget: android_usb ready
[    3.481479] usb: udc_enable
[    3.481700] mousedev: PS/2 mouse device common for all mice
[    3.482059] input: ft5x0x_ts as /devices/virtual/input/input0
[    3.517735] hub 1-2:1.0: 5 ports detected
[    3.521895] ft5x0x_ts 1-0038: Firmware version 0x18
[    3.526374] ft5x0x_ts 1-0038: FocalTech ft5x0x TouchScreen initialized
[    3.533350] touchscreen-1wire        initialized
[    3.536881] backlight-1wire  initialized
[    3.540781] setup_irq: ret = 0
[    3.543804] PWM clock = 100000000
[    3.547030] TCNT_FOR_SAMPLE_BIT = 650, TCFG1 = 00010004
[    3.552536] input: fa_ts_input as /devices/virtual/input/input1
[    3.558528] ts-if    initialized
[    3.561226] wake enabled for irq 378
[    3.564670] wake enabled for irq 379
[    3.568237] wake enabled for irq 380
[    3.571794] wake enabled for irq 381
[    3.575328] GPIO Input Driver: Start gpio inputs for tiny4412-key in interrupt mode
[    3.583156] input: tiny4412-key as /devices/virtual/input/input2
[    3.589558] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[    3.594404] s3c-rtc exynos-rtc: rtc disabled, re-enabling
[    3.599754] s3c-rtc exynos-rtc: warning: invalid RTC value so initializing it
[    3.606854] 4: TCNTB=0000028a, TCNTO=000001d9, TINT_CSTAT=00000008
[    3.613386] using rtc device, s3c, for alarms
[    3.617183] s3c-rtc exynos-rtc: rtc core: registered s3c as rtc0
[    3.623449] i2c /dev entries driver
[    3.627685] Linux media interface: v0.10
[    3.630960] lirc_dev: IR Remote Control driver registered, major 249
[    3.637131] IR NEC protocol handler initialized
[    3.641661] IR RC5(x) protocol handler initialized
[    3.646425] IR RC6 protocol handler initialized
[    3.650939] IR JVC protocol handler initialized
[    3.655459] IR Sony protocol handler initialized
[    3.655464] IR RC5 (streamzap) protocol handler initialized
[    3.655468] IR LIRC bridge handler initialized
[    3.655519] Registered IR keymap rc-empty
[    3.655811] input: gpio_ir_recv as /devices/virtual/rc/rc0/input3
[    3.655955] rc0: gpio_ir_recv as /devices/virtual/rc/rc0
[    3.656151] rc rc0: lirc_dev: driver ir-lirc-codec (gpio-rc-recv) registered at minor = 0
[    3.656345] Linux video capture interface: v2.00
[    3.656438] gspca: v2.13.0 registered
[    3.656619] exynos-mdev: Media65535[0xdb9c3c00] was registered successfully
[    3.656776] [INFO]flite_probe:2126: FIMC-LITE0 probe success
[    3.656801] [INFO]flite_probe:2126: FIMC-LITE1 probe success
[    3.657369] fimc_is_init_mem_mgr : [cma_info] start_addr : 0x58000000, end_addr : 0x58bcc000, total_size : 0xbcc000, free_size : 0xbcc000
[    3.670955] ctrl->mem.base = 0x58000000
[    3.670961] ctrl->mem.size = 0xbcc000
[    3.670965] ctrl->mem.fw_ref_base = 0x58a01000
[    3.670968] ctrl->mem.setfile_ref_base = 0x58b81000
[    3.671205] FIMC-IS probe completed
[    3.671653] s3c-csis: Samsung MIPI-CSIS0 driver probed successfully
[    3.671700] s3c-csis: Samsung MIPI-CSIS1 driver probed successfully
[    3.671839] Initialize JPEG driver
[    3.672162] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video12
[    3.672301] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video11
[    3.672472] S5P HPD Driver, (c) 2009 Samsung Electronics
[    3.672652] s5p_int_src_ext_hpd()
[    3.672661] s5p_hpd_read_gpio(0)
[    3.672989] s5p_hpd_read_gpio(0)
[    3.673360] i2c i2c-7: attached s5p_ddc into i2c adapter successfully
[    3.673447] i2c-core: driver [s5p_ddc] using legacy suspend method
[    3.673452] i2c-core: driver [s5p_ddc] using legacy resume method
[    3.673610] mfc_init_mem_mgr[587] cma 0x42100000 0x45200000 0x3100000 0x3100000 1
[    3.673624] mfc_init_mem_mgr[649]: base 0x42100000, size 0x3100000, addr 0xc2100000
[    3.673981] MFC(Multi Function Codec - FIMV v5.x) registered successfully
[    3.674374] Samsung Graphics 2D driver, (c) 2011 Samsung Electronics
[    3.674634] usbcore: registered new interface driver uvcvideo
[    3.674638] USB Video Class driver (v1.1.0)
[    3.717818] input: mma7660 as /devices/platform/s3c2440-i2c.3/i2c-3/3-004c/input/input4
[    3.718057] mma7660 3-004c: MMA7660 device is probed successfully.
[    3.718151] i2c-core: driver [mma7660] using legacy suspend method
[    3.718156] i2c-core: driver [mma7660] using legacy resume method
[    3.718165] MMA7660 sensor driver registered.
[    3.718169] S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[    3.718413] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
[    3.718926] device-mapper: uevent: version 1.0.3
[    3.719230] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[    3.719929] cpuidle: using governor ladder
[    3.915244] Front
[    3.917566] cpuidle: using governor menu
[    3.921610] dw_mmc dw_mmc: Using internal DMA controller.
[    3.926457] dw_mmc dw_mmc: Version ID is 240a
[    3.930518] dw_mmc dw_mmc: DW MMC controller at irq 141, 32 bit host data width, 128 deep fifo
[    3.939280] sdhci: Secure Digital Host Controller Interface driver
[    3.945269] sdhci: Copyright(c) Pierre Ossman
[    3.949677] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (100000000 Hz)
[    3.956498] mmc1: no vmmc regulator found
[    3.960047] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[    3.970510] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[    3.977182] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (100000000 Hz)
[    3.984022] mmc2: no vmmc regulator found
[    3.988218] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[    3.991706] mmc0: PERM_WRITE_PROTECT was set.
[    3.991712] mmc0: 4YMD3R: 15010034594d4433520144aab049829b
[    4.005752] usbcore: registered new interface driver usbhid
[    4.010369] usbhid: USB HID core driver
[    4.014508] logger: created 2048K log 'log_main'
[    4.018969] logger: created 256K log 'log_events'
[    4.023608] logger: created 1024K log 'log_radio'
[    4.028304] logger: created 256K log 'log_system'
[    4.032961] logger: created 256K log 'log_sf'
[    4.037502] zram: num_devices not specified. Using default: 1
[    4.042937] zram: Creating 1 devices ...
[    4.047578] usbcore: registered new interface driver snd-usb-audio
[    4.053849] Samsung Audio Subsystem Driver, (c) 2011 Samsung Electronics
[    4.056205] mmc0 : 00 : 00 : 00000000 : 0.
[    4.056213] mmc0 : disable PON feature : 15 : 00 : 00000000
[    4.064324] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
[    4.064542] mmc0: new high speed DDR MMC card at address 0001
[    4.064867] mmcblk0: mmc0:0001 4YMD3R 3.64 GiB
[    4.066280]  mmcblk0: p1 p2 p3 p4
[    4.092746] audss_init: RCLK SRC[i2sclk]
[    4.096830] Samsung SRP driver, (c)2011 Samsung Electronics
[    4.103065] ALSA device list:
[    4.105065]   No soundcards found.
[    4.108538] GACT probability NOT on
[    4.110127] usb 1-2.4: new high speed USB device number 3 using s5p-ehci
[    4.118610] Mirror/redirect action on
[    4.122258] u32 classifier
[    4.124930]     Actions configured
[    4.128327] Netfilter messages via NETLINK v0.30.
[    4.133091] nf_conntrack version 0.5.0 (11874 buckets, 47496 max)
[    4.139668] ctnetlink v0.93: registering with nfnetlink.
[    4.144414] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    4.151343] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    4.157443] xt_time: kernel timezone is -0000
[    4.161624] ip_tables: (C) 2000-2006 Netfilter Core Team
[    4.166915] arp_tables: (C) 2002 David S. Miller
[    4.171411] TCP cubic registered
[    4.175279] NET: Registered protocol family 10
[    4.179395] Mobile IPv6
[    4.181474] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    4.183170] mmc1: new high speed SDHC card at address 5b1f
[    4.183479] mmcblk1: mmc1:5b1f SE04G 3.66 GiB
[    4.185032]  mmcblk1: p1
[    4.199367] IPv6 over IPv4 tunneling driver
[    4.204503] NET: Registered protocol family 17
[    4.207861] NET: Registered protocol family 15
[    4.212275] NET: Registered protocol family 35
[    4.215358] usb 1-2.4: config 1 interface 0 altsetting 0 endpoint 0x83 has an invalid bInterval 0, changing to 9
[    4.226933] EXYNOS4X12: Adaptive Support Voltage init
[    4.231881] EXYNOS4X12(SG):  ORIG : 3 MOD : 0 RESULT : 3
[    4.237202] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    4.244812] Registering SWP/SWPB emulation handler
[    4.249594] DVFS : VDD_ARM Voltage table set with 3 Group
[    4.255151] cpufreq_interactive_input_connect: connect to ft5x0x_ts
[    4.261234] cpufreq_interactive_input_connect: connect to fa_ts_input
[    4.268866] s3c-rtc exynos-rtc: setting system clock to 2014-01-01 12:00:00 UTC (1388577600)
[    4.276394] FIMC0 registered successfully
[    4.280325] FIMC1 registered successfully
[    4.284313] FIMC2 registered successfully
[    4.288290] FIMC3 registered successfully
[    4.292224] S5P TVOUT Driver v3.0 (c) 2010 Samsung Electronics
[    4.297874] usb 1-2.4: New USB device found, idVendor=0a46, idProduct=9621
[    4.304707] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    4.312845] dm962x: dm_read_reg() 0x29 0x0a
[    4.316219] dm962x: dm_read_reg() 0x28 0x46
[    4.320470] dm962x: dm_read_reg() 0x2b 0x96
[    4.324595] dm962x: dm_read_reg() 0x2a 0x21
[    4.328853] dm962x: dm_read_reg() 0xF2 0x00
[    4.332926] dm962x:  [Analysis.2] 0xF2, D[7] 0 OK
[    4.337613] dm962x:  [Analysis.2] 0xF2, D[6] 0 OK
[    4.342290] dm962x:  [Analysis.2] 0xF2, D[5] 0 EP1: Empty
[    4.347686] dm962x:  [Analysis.2] 0xF2, D[3] 0 OK
[    4.352346] dm962x:  [Analysis.2] 0xF2, D[2] 0 OK
[    4.356994] dm962x:  [Analysis.2] 0xF2, D[1] 0 OK
[    4.361712] dm962x:  [Analysis.2] 0xF2, D[0] 0 Status: TX buffer 0 pkts
[    4.368518] hotplug_policy_init: intialised with policy : DVFS_NR_BASED_HOTPLUG
[    4.371867] dm962x: ethernet MAC address 1c:6f:65:34:51:7e (param data)
[    4.372231] dm962x: 9620 Mode = 128
[    4.385906] Freeing init memory: 240K
[    4.386043] dm9620 1-2.4:1.0: eth0: register 'dm9620' at usb-s5p-ehci-2.4, Davicom DM9620 USB Ethernet, 1c:6f:65:34:51:7e
[    4.485146] usb 1-2.5: new high speed USB device number 4 using s5p-ehci
[    4.591644] usb 1-2.5: New USB device found, idVendor=0424, idProduct=2530
[    4.591792] usb 1-2.5: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    4.591939] usb 1-2.5: Product: Bridge device
[    4.853339] init: /dev/hw_random not found
[    5.073423] init: /dev/hw_random not found
[    5.087992] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    5.088461] fs_mgr: __mount(source=/dev/block/mmcblk0p2,target=/system,type=ext4)=0
[    5.113681] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.113777] mmcblk0: command error, retrying timeout
[    5.114274] EXT4-fs (mmcblk0p4): warning: checktime reached, running e2fsck is recommended
[    5.114517] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.120093] mmcblk0: command error, retrying timeout
[    5.125312] EXT4-fs (mmcblk0p4): recovery complete
[    5.129899] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.137514] mmcblk0: command error, retrying timeout
[    5.142623] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[    5.152638] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.160261] mmcblk0: command error, retrying timeout
[    5.166154] fs_mgr: __mount(source=/dev/block/mmcblk0p4,target=/cache,type=ext4)=0
[    5.205977] MFC F/W loaded successfully (size: 376448)
[    5.622935] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.623033] mmcblk0: command error, retrying timeout
[    5.623486] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.623579] mmcblk0: command error, retrying timeout
[    5.626397] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.633770] mmcblk0: command error, retrying timeout
[    5.639005] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.646454] mmcblk0: command error, retrying timeout
[    5.651571] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.659096] mmcblk0: command error, retrying timeout
[    5.664261] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.671773] mmcblk0: command error, retrying timeout
[    5.676965] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.684442] mmcblk0: command error, retrying timeout
[    5.689628] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.697122] mmcblk0: command error, retrying timeout
[    5.702282] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.709787] mmcblk0: command error, retrying timeout
[    5.714717] 3: TCNTB=0000028a, TCNTO=000000ea, TINT_CSTAT=00000008
[    5.721217] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.728626] mmcblk0: command error, retrying timeout
[    5.733809] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.741301] mmcblk0: command error, retrying timeout
[    5.746478] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.753968] mmcblk0: command error, retrying timeout
[    5.759139] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.766650] mmcblk0: command error, retrying timeout
[    5.771829] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.779314] mmcblk0: command error, retrying timeout
[    5.784538] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.791993] mmcblk0: command error, retrying timeout
[    5.797176] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.804662] mmcblk0: command error, retrying timeout
[    5.809860] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.817338] mmcblk0: command error, retrying timeout
[    5.822498] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.830016] mmcblk0: command error, retrying timeout
[    5.835223] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.842680] mmcblk0: command error, retrying timeout
[    5.847865] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.855356] mmcblk0: command error, retrying timeout
[    5.860579] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.868024] mmcblk0: command error, retrying timeout
[    5.873216] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.880702] mmcblk0: command error, retrying timeout
[    5.886088] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.893375] mmcblk0: command error, retrying timeout
[    5.898605] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.906045] mmcblk0: command error, retrying timeout
[    5.911294] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.918718] mmcblk0: command error, retrying timeout
[    5.923904] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.931393] mmcblk0: command error, retrying timeout
[    5.936596] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.944062] mmcblk0: command error, retrying timeout
[    5.949288] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.956732] mmcblk0: command error, retrying timeout
[    5.962096] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.969411] mmcblk0: command error, retrying timeout
[    5.974588] EXT4-fs (mmcblk0p3): recovery complete
[    5.979213] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    5.986856] mmcblk0: command error, retrying timeout
[    5.991975] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,noauto_da_alloc,errors=panic
[    6.003326] fs_mgr: __mount(source=/dev/block/mmcblk0p3,target=/data,type=ext4)=0
[    6.011549] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400d00
[    6.018454] mmcblk0: command error, retrying timeout
[    6.060213] binder: 1610:1610 transaction failed 29189, size 0-0
[    6.063218] init: cannot find '/system/bin/setup_fs', disabling 'setup_fs'
[    6.076251] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
[    6.076349] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
[    6.084194] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
[    6.094954] adb_open
[    6.095169] DUN is registerd
[    6.095211] adb_bind_config
shell@tiny4412:/ $ [    6.237055] FriendlyARM http://www.arm9.net
[    6.329547] type=1400 audit(1388577602.550:3): avc: denied { execmem } for pid=1620 comm="rild" scontext=u:r:rild:s0 tcontext=u:r:rild:s0 tclass=process
[    6.347765] asoc: wm8960-hifi <-> samsung-i2s.0 mapping ok
[    6.348570] asoc: wm8960-hifi <-> samsung-i2s.4 mapping ok
[    6.358137] s3c-fimc3: FIMC3 1 opened.
[    6.487103] usbcore: registered new interface driver rtl8192cu
[    6.637277] RTL871X: rtl8188eu driver version=v4.1.5_7309.20130425
[    6.637354] RTL871X: build time: Mar 24 2015 16:54:54
[    6.639076] usbcore: registered new interface driver rtl8188eu
[    6.761216] Compat-drivers backport release: compat-drivers-v3.8.3-2-snpu
[    6.761301] Backport based on linux-stable.git v3.8.3
[    6.761360] compat.git: linux-stable.git
[    6.858357] [HPD_IF] s5p_hpd_ioctl: HPD status is unplugged
[    6.903304] cfg80211: Calling CRDA to update world regulatory domain
[    6.997579] libertas_sdio: Libertas SDIO driver
[    6.997632] libertas_sdio: Copyright Pierre Ossman
[    7.061085] healthd: wakealarm_init: timerfd_create failed
[    7.061307] healthd: No charger supplies found
[    7.061365] healthd: No battery devices found
[    7.140731] usbcore: registered new interface driver ath9k_htc
[    7.324514] usbcore: registered new interface driver rt73usb
[    7.449006] usbcore: registered new interface driver rt2800usb
[    7.555427] usbcore: registered new interface driver zd1211rw
[    7.753496] s3cfb s3cfb.0: [fb3] win0: Alloc dma: 0x48200000, size: 0x00465000
[    7.753624] s3c-fimc3: FIMC3 2 opened.